Standard Solenoids
All Cryomagnetics' niobium-titanium magnets are wound using
multi-filamentary superconductor twisted within a copper matrix. The wire is carefully
chosen to provide maximum magnetic stability and minimum hysteresis. The coils are fully
impregnated with a special high thermal conductivity epoxy to prevent wire slippage (and
thus magnet training) from occurring. All magnets are fully quench protected not only by
means of the copper matrix of the wire, but also through the use of protective diodes.
Using diodes for quench protection instead of resistors guarantees linear charging of the
magnet and minimizes heat input into the cryostat during charge/discharge cycles. All
coils are tested to full field and quenched to insure that coil performance meets
specifications without degradation.
The standard solenoids all achieve rated magnetic field at 4.2K. In general, a 20%
increase in this rated field can be achieved by operating the magnets at 2.2K, either by
pumping on the liquid helium bath or through the use of a lambda plate. All 9T solenoids
listed, for example, are capable of 11T at 2.2K. If operation beyond the 4.2K rated field
is desired, however, it should be specified when the magnet is ordered. In general, all
standard solenoids are designed to be able to achieve their 2.2K field at less than 100
amperes. All bore sizes quoted are nominal -- that is, the actual bore size is large
enough to allow clear passage of a tube with an O.D. the size of the specified bore.
Custom applications are quoted by request. Contact us with your
specifications.
Standard 5T Solenoids
| Model |
Bore |
Homogeneity*
|
Current |
Inductance |
50-100-050L |
1.00" |
+/- 0.5% |
44A |
1.1H |
50-100-010L |
1.00" |
+/- 0.1% |
48A |
1.5H |
50-150-050L |
1.50" |
+/- 0.5% |
47A |
1.2H |
50-150-010L |
1.50" |
+/- 0.1% |
52A |
1.7H |
50-200-050L |
2.00" |
+/- 0.5% |
44A |
3.3H |
50-200-010L |
2.00" |
+/- 0.1% |
49A |
3.5H |
50-250-050L |
2.50" |
+/- 0.5% |
48A |
4.5H |
50-250-010L |
2.50" |
+/- 0.1% |
50A |
5.5H |
50-300-050 |
3.00" |
+/- 0.5% |
78A |
2.5H |
50-300-010 |
3.00" |
+/- 0.1% |
74A |
4.0H |
Standard 6T Solenoids
| Model |
Bore |
Homogeneity*
|
Current |
Inductance |
60-100-050L |
1.00" |
+/- 0.5% |
45A |
1.5H |
60-100-010L |
1.00" |
+/- 0.1% |
45A |
1.7H |
60-150-050L |
1.50" |
+/- 0.5% |
50A |
2.0H |
60-150-010L |
1.50" |
+/- 0.1% |
52A |
2.4H |
60-200-050L |
2.00" |
+/- 0.5% |
44A |
5.6H |
60-200-010L |
2.00" |
+/- 0.1% |
49A |
8.6H |
60-250-050L |
2.50" |
+/- 0.5% |
45A |
7.9H |
60-250-010 |
2.50" |
+/- 0.1% |
76A |
4.8H |
60-300-050 |
3.00" |
+/- 0.5% |
74A |
5.1H |
60-300-010 |
3.00" |
+/- 0.1% |
76A |
6.8H |
Standard 7T Solenoids
| Model |
Bore |
Homogeneity*
|
Current |
Inductance |
70-100-050L |
1.00" |
+/- 0.5% |
48A |
1.8H |
70-100-010L |
1.00" |
+/- 0.1% |
48A |
2.0H |
70-150-050L |
1.50" |
+/- 0.5% |
48A |
2.1H |
70-150-010L |
1.50" |
+/- 0.1% |
49A |
2.5H |
70-200-050L |
2.00" |
+/- 0.5% |
48A |
5.9H |
70-200-010L |
2.00" |
+/- 0.1% |
48A |
9.1H |
70-250-050L |
2.50" |
+/- 0.5% |
47A |
8.5H |
70-250-010L |
2.50" |
+/- 0.1% |
47A |
10.0H |
70-300-050L |
3.00" |
+/- 0.5% |
50A |
14.5H |
70-300-010L |
3.00" |
+/- 0.1% |
46A |
18.2H |
Standard 8T Solenoids
| Model |
Bore |
Homogeneity*
|
Current |
Inductance |
80-100-050 |
1.00" |
+/- 0.5% |
75A |
2.2H |
80-100-010 |
1.00" |
+/- 0.1% |
76A |
3.0H |
80-150-050 |
1.50" |
+/- 0.5% |
79A |
2.4H |
80-150-010 |
1.50" |
+/- 0.1% |
78A |
3.0H |
80-200-050 |
2.00" |
+/- 0.5% |
86A |
3.5H |
80-200-010 |
2.00" |
+/- 0.1% |
76A |
4.2H |
80-250-050 |
2.50" |
+/- 0.5% |
80A |
6.7H |
80-250-010 |
2.50" |
+/- 0.1% |
79A |
8.9H |
80-300-050 |
3.00" |
+/- 0.5% |
83A |
9.9H |
80-300-010 |
3.00" |
+/- 0.1% |
78A |
11.3H |
Standard 9T Solenoids
| Model |
Bore |
Homogeneity*
|
Current |
Inductance |
90-100-010 |
1.00" |
+/- 0.1% |
76A |
3.0H |
90-150-010 |
1.50" |
+/- 0.1% |
78A |
3.0H |
90-200-010 |
2.00" |
+/- 0.1% |
76A |
4.2H |
90-200-010L |
2.00" |
+/- 0.1% |
40A |
32.0H |
90-250-010 |
2.50" |
+/- 0.1% |
79A |
8.9H |
| 90-250-010L |
2.50" |
+/- 0.1% |
40A |
56.5H |
90-300-010 |
3.00" |
+/- 0.1% |
78A |
11.3H |
| 90-300-010L |
3.00" |
+/- 0.1% |
40A |
48.0H |
* Homogeneity is measured over a 10mm diameter spherical volume (DSV). The above is a
small sampling of the many magnets we have manufactured.
sales@cryomagnetics.com
Please contact us for more information!
1006 Alvin Weinberg Drive
Oak Ridge, Tennessee 37830
USA
Phone: (865) 482-9551
Fax: (865) 483-1253
Return to Superconducting Magnets Page